Dassault catia system requirements | These requirements should be as follows.
Disk drive
An internal or external disk drive (minimum recommended size 4 GB) is required to store executable program data. All CATIA V5 product Installation requires Microsoft 2.0 GB (R) Windows (R), 2.4 GB on AIX (R), 2.7 GB on HP on-UX, 2.3 GB on Solaris system requirement.
Memory
A minimum of 256 MB of RAM is recommended for all applications. 512 MB RAM or more is recommended for DMU applications. In Digitized Shape Editor 2 (DSE), however (in big data conditions) the amount of RAM can be greater than the amount used.
Internal / External drives
A CD-ROM drive is required for program installation. It also requires optional disc for access and downloadable online documentation.
Display
A graphic color Display-specific graphics card compatible with the selected platform. For minimum usability reasons, the recommended monitor size is 17 inches.
Minimum resolution for Windows workstations is 1024 x 768. UNIX workstations require 1280 x 1024.
Keyboard
A specific keyboard with native compatible national language support is required.
pointing device (Mouse)
Three button mouse. On Windows workstations, a two-button mouse alternative (the third button on the keyboard sequence) can be used to emulate. A three-button mouse is recommended for usability reasons. Intell Mouse (two buttons plus a third button instead of a wheel) can be an alternative to the button mouse on three Windows workstations. As the wheel center button, it works to provide additional manipulations such as panning and scrolling.
*Optional components and features:
CATIA P2 and P3, SpaceBall or SpaceMouse can be used, besides the standard mouse, to perform graphic manipulations (Pan, alternately) Zoom. The necessary drivers are provided with these devices. Support for these devices is also available in DMU Guide 1 and DMU Space Analysis 1 P1.
The overall solution and robustness depend on the operating system and robustness used in the hardware environment. Windows XP and UNIX hardware configurations are published by Dassault Systemes as certified to run CATIA V5 products.
Although CATIA V5 product configurations or graphics adapters other than the specifications listed above for each of these platforms, special configurations or adapters may not be accepted for support.
CATIA History
CATIA software was started as an in-house development by French aircraft manufacturer Avions Marcel Dassault in 1977, at the time the company was a user of CADAM software.
It was originally called CATI (Conception Assistée Tridimensionnelle Interactive — French for Coordinated 3D Design) — later renamed CATIA in 1981, when Dassault established a subsidiary to develop and sell this software, it entered into a distribution agreement with IBM, giving it a divisional privilege.
In 1984, Boeing chose CATIA as its main 3D design tool, thus becoming the software’s largest customer.
In 1988, CATIA version 3 was created to run on UNIX-powered computers.
In 1990, General Dynamics Electric Boat company chose CATIA as its main 3D design tool to manufacture Virginia-type submarines for the United States Navy. (U.S. Navy’s Virginia class submarine)
In 1992, CADAM was acquired by IBM, and CATIA CADAM Version 4 was released the following year. In 1996, it was ported from one to four Unix operating systems, including IBM AIX, Silicon Graphics IRIX, Sun Microsystems SunOS and Hewlett-Packard HP-UX.
In 1998, a completely rewritten version of CATIA was released with CATIA Version 5 UNIX support, the software has been supporting Windows NT and Windows XP since 2001.
In 2008, Dassault announced and launched CATIA Version 6.
Supported Operating Systems:
CATIA Version 6 runs on Windows XP 32/64 bit, Windows Vista 64 bit, Windows 7 64 bit and UNIX platforms.
CATIA Version 5 works with 32-bit and 64-bit versions of Microsoft Windows, and it started working on Windows Vista (64-bit) after the release of Service Pack 4. IBM AIX (operating system), Hewlett Packard HP-UX (operating system), and Sun Microsystems Solaris operating system are now supported.
With CATIA Version 4, computer support using Unix started.
CATIA Version 3 and earlier versions work on most commonly used computers.
